Category: copper-catalyst

Copper(I) bromide, cas is 7787-70-4, it is a common heterocyclic compound, the copper-catalyst compound, its synthesis route is as follows.,7787-70-4

General procedure: 0.018g (0.182mmol) of CuCl was added to 0.340g (0.205mmol) of [PPh4]2[1] dissolved in 20mL of MeCN solution. After stirring the resultant solution for 1hat RT, the yellowish brown solution formed, which was filtered, and solvent was removed in vacuo. The precipitate was washed with Et2O and extracted with THF, then recrystallized with Et2O/MeOH/THF to give [PPh4]2[2a] (0.250g, 0.143mmol, 79% based on CuCl). Similarly, under the same reaction conditions, using CuBr and CuI, we have isolated a yellowish brown solid of [PPh4]2[2b] (96% based on CuBr) and [PPh4]2[2c] (71% based on CuI), respectively, upon crystallization from Et2O/THF.

With the rapid development of chemical substances, we look forward to future research findings about Copper(I) bromide

Reference£º
Article; Shieh, Minghuey; Miu, Chia-Yeh; Liu, Yu-Hsin; Chu, Yen-Yi; Hsing, Kai-Jieah; Chiu, Jung-I; Lee, Chung-Feng; Journal of Organometallic Chemistry; vol. 815-816; (2016); p. 74 – 83;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

Name is Copper(II) trifluoromethanesulfonate, as a common heterocyclic compound, it belongs to copper-catalyst compound, and cas is 34946-82-2, its synthesis route is as follows.,34946-82-2

In a 20 mL vial with heating, anhydrous copper(II) trifluoromethanesulfonate(221 mg, 0.61 mmol) was dissolved in 15 mL of90% EtOH. After cooling to room temperature, HL1 (200 mg,0.61 mmol) was added to the pale blue solution, which became bluegreen.The mixture was heated to boiling to ensure all reactants weredissolved, and then cooled to room temperature, at which point thesolution was green-blue and contained a teal precipitate. The precipitatewas isolated via gravity filtration as a bright teal powder (256 mg, 71%). HR-MS (ESI, MeOH) m/z: [L1Cu]+ Calcd. for[CuC20H12N3O2]+ 389.0226; found 388.9763; m/z [L1CuII(EtOH)]+Calcd. for [CuC32H18N3O3]+ 435.0644; found 435.0132 (Fig. S4). Anal.Calc. for CuC21H14N3O6SF3: C, 45.29; H, 2.53; N, 7.54. Found: C, 45.06;H, 2.74; N, 8.09. X-ray quality crystals in the form of teal blocks weregrown upon slow diffusion of anhydrous THF into a concentrated solutionof the compound in EtOH at room temperature.

With the complex challenges of chemical substances, we look forward to future research findings about Copper(II) trifluoromethanesulfonate

Reference£º
Article; Elwell, Courtney E.; Neisen, Benjamin D.; Tolman, William B.; Inorganica Chimica Acta; vol. 485; (2019); p. 131 – 139;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

It is a common heterocyclic compound, the copper-catalyst compound, Copper(I) bromide, cas is 7787-70-4 its synthesis route is as follows.,7787-70-4

A solution of CuBr (0.0173 g, 0.12 mmol) in 10 mL of acetonitrile was added dropwise to a solution of 4 (0.048 g, 0.12 mmol) in 10 mL of dichloromethane at room temperature. The reaction mixture was stirred for 4 h. The solvent was removed under reduced pressure to obtain 8 as a brown crystalline solid. Yield: 82% (0.054 g). Mp: >195 C (dec). Anal. Calc. for C42H44Cu2Br2N2P2Se2¡¤CH3CN: C, 46.99; H, 4.21; N, 3.74. Found: C, 46.77; H, 4.10; N, 3.79%. 1H NMR (400 MHz, CDCl3) delta 7.73-7.02 (m, Ar, 28H), 3.43 (s, CH2, 4H), 2.46 (s, NMe2, 12H). 31P{1H} NMR (162 MHz, CDCl3): delta 23.2 (br s).

With the complex challenges of chemical substances, we look forward to future research findings about Copper(I) bromide

Reference£º
Article; Ananthnag, Guddekoppa S.; Edukondalu, Namepalli; Mague, Joel T.; Balakrishna, Maravanji S.; Polyhedron; vol. 62; (2013); p. 203 – 207;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

Name is Copper(II) trifluoromethanesulfonate, as a common heterocyclic compound, it belongs to copper-catalyst compound, and cas is 34946-82-2, its synthesis route is as follows.

A solution of Cu(OTf)2 (90.0 mg, 0.249 mM, OTf = trifluormethansulfonate) in methanol was added to a solution of HLpz (53.5 mg,0.250 mM) and triethylamine (25.0 mg, 0.250 mM) in methanol, affording a dark green solution. A solution of excess 4,4-bipyridine (4,4-bipy) was layered on the above solution, from which purple crystals of 1 suitable for X-ray analysis were obtained. Yield: 86 mg, 68%. Anal. Calcd for C34H26Cu2F6N10O8S2: C, 40.52; H, 2.60; N, 13.90. Found: C, 40.27;H, 2.53; N, 13.63. FTIR (KBr): 3447, 1647, 1416, 1380, 1291, 1245, 1224, 1158, 1033,816, 772, 638, 518 cm-1. ESI-MS (MeOH): m/z = 276 [Cu(Lpz)]+, 432 [Cu(Lpz)(4,4-bipy)]+, 490 [Cu(Lpz)2 + H]+.

34946-82-2, In the field of chemistry, the synthetic routes of compounds are constantly being developed and updated. I will also mention this compound in other articles.,34946-82-2 ,Copper(II) trifluoromethanesulfonate, other downstream synthetic routes, hurry up and to see

Reference£º
Article; Houser, Robert P.; Wang, Zhaodong; Powell, Douglas R.; Hubin, Timothy J.; Journal of Coordination Chemistry; vol. 66; 23; (2013); p. 4080 – 4092;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

It is a common heterocyclic compound, the copper-catalyst compound, Copper(I) bromide, cas is 7787-70-4 its synthesis route is as follows.

General procedure: 0.022g (0.222mmol) of CuCl was added to 0.180g (0.109mmol) of [PPh4]2[1] dissolved in 20mL of MeCN solution at -35C. After stirring the resultant solution for 5min, the yellowish brown solution formed, which was filtered, and the filtrate was concentrated. A solution of Et2O (60mL) was added into the filtrate to precipitate the product at -35C. The precipitate was then washed with Et2O and dried to give [PPh4]2[3a] (0.107g, 0.058mmol, 53% based on [PPh4]2[1]). Similarly, under the same reaction conditions, using CuBr, we have isolated a yellowish brown solid of [PPh4]2[3b] (80% based on [PPh4]2[1]) upon crystallization from Et2O/MeCN.

7787-70-4, In the field of chemistry, the synthetic routes of compounds are constantly being developed and updated. I will also mention this compound in other articles.,7787-70-4 ,Copper(I) bromide, other downstream synthetic routes, hurry up and to see

Reference£º
Article; Shieh, Minghuey; Miu, Chia-Yeh; Liu, Yu-Hsin; Chu, Yen-Yi; Hsing, Kai-Jieah; Chiu, Jung-I; Lee, Chung-Feng; Journal of Organometallic Chemistry; vol. 815-816; (2016); p. 74 – 83;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

It is a common heterocyclic compound, the copper-catalyst compound, Copper(II) trifluoromethanesulfonate, cas is 34946-82-2 its synthesis route is as follows.

Cu (CF3 SO3 )2 And 4 – (3 – (4H – 1,2, 4 – triazole -4 – yl) phenyl) – 4H – 1,2, 4 – triazole) (L) in a molar ratio of 1:1; L (0.0424 g, 0.2 mmol), Cu (CF3 SO3 )2 (0.0691 g, 0.2 mmol), H2 O (6 ml), CH3 CN (4 ml), water heat 160 o C three days after cooling to room temperature. After operates the cauldron X – ray single crystal diffraction analysis is yellow rod-like crystal. Yield: 35% (calculated on the basis of L). Elemental analysis (C33 H26 Cu3 F9 N18 O10 S3 ) Theoretical value (%): C, 30.67; H, 2.03; N, 19.51. The measured value: C, 30.69; H, 2.06; N, 19.59. We also tried other proportions, for example Cu (CF3 SO3 )2 And L in a molar ratio of 2:1, irrespective of the length of the water heat reaction time, are not crystalline compound. Therefore Cu (CF3 SO3 )2 And L in a molar ratio of 1:1 is the best reaction mixture ratio.

34946-82-2, In the field of chemistry, the synthetic routes of compounds are constantly being developed and updated. I will also mention this compound in other articles.,34946-82-2 ,Copper(II) trifluoromethanesulfonate, other downstream synthetic routes, hurry up and to see

Reference£º
Patent; Tianjin Normal University; Wang, Ying; (12 pag.)CN104557982; (2017); B;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

7787-70-4, In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact. Copper(I) bromide, cas is 7787-70-4,the copper-catalyst compound, it is a common compound, a new synthetic route is introduced below.

Synthesis of [(SIMes)CuBr]. In an oven-dried vial, copper(I) bromide (0.522 g, 3.63 mmol), SIMes.HCl (0.86 g, 2.52 mmol) and sodium tert-butoxide (0.243 g, 2.52 mmol) were loaded inside a glovebox and stirred in dry THF (18 mL) overnight at room temperature outside of the glovebox. After filtration of the reaction mixture through a plug of Celite, the filtrate was mixed with hexane to form a precipitate. A second filtration afforded 0.808 g (71% yield) of the title complex as an off-white solid.Spectroscopic and analytical data for [(SIMes)CuBr]: 1H NMR (300 MHz, [D6]acetone): delta=7.01 (s, 4H, HAr), 4.16 (s, 4H, NCH2), 2.37 (s, 12H, ArCH3), 2.29 (s, 6H, ArCH3); 13C NMR (75 MHz, CDCl3): delta=202.6 (C, NCN), 138.5 (C, CAr), 135.3 (CH, CAr), 135.0 (C, CAr), 129.7 (CH, CAr), 51.0 (CH2, NCH2), 21.0 (CH3, ArCH3), 18.0 (CH3, ArCH3); Elemental analysis calcd for C21H26BrCuN2 (449.89): C, 56.06; H, 5.83; N, 6.23. Found: C, 55.98; H, 5.64; N, 6.21%.

The chemical industry reduces the impact on the environment during synthesis,7787-70-4,Copper(I) bromide,I believe this compound will play a more active role in future production and life.

Reference£º
Patent; Institut Catala d’Investigacio Quimica; Institucio Catalana de Recerca i Estudis Avancats; US2009/69569; (2009); A1;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

Name is Copper(II) trifluoromethanesulfonate, as a common heterocyclic compound, it belongs to copper-catalyst compound, and cas is 34946-82-2, its synthesis route is as follows.

General procedure: A mixture of ligand L (23.1 mg, 55 mumol) and appropriate metalsalt (55 mumol) in nitromethane (20 mL) was stirred at room temperaturefor 48 h under the normal atmosphere. The complexeswere isolated as a solids by evaporation of the solvent and followedby a dissolution of the residue in the minimum volume of CH3CNand precipitation of the complexes by the gradual addition ofether. Obtained solids were filtered off and dried in air.

34946-82-2, In the field of chemistry, the synthetic routes of compounds are constantly being developed and updated. I will also mention this compound in other articles.,34946-82-2 ,Copper(II) trifluoromethanesulfonate, other downstream synthetic routes, hurry up and to see

Reference£º
Article; Wa??sa-Chorab, Monika; Marcinkowski, Dawid; Kubicki, Maciej; Hnatejko, Zbigniew; Patroniak, Violetta; Polyhedron; vol. 118; (2016); p. 1 – 5;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

Copper(I) bromide, cas is 7787-70-4, it is a common heterocyclic compound, the copper-catalyst compound, its synthesis route is as follows.,7787-70-4

General procedure: To a solution of (S,S)-iPr-pheboxH (0.051g, 0.173mmol) in dichloromethane (15mL), the corresponding copper(I) salt CuX (X=Cl, Br, I) (0.347mmol) was added and the mixture stirred at room temperature during 24h. Then, the reaction mixture was filtered via cannula, concentrated under reduced pressure to ca. 2mL and diethyl ether/n-hexane (1:2) (30mL) was added. The resulting solid was washed with n-hexane (3¡Á5mL) and vacuum-dried.

7787-70-4 is used more and more widely, we look forward to future research findings about Copper(I) bromide

Reference£º
Article; Vega, Esmeralda; De Julian, Eire; Borrajo, Gustavo; Diez, Josefina; Lastra, Elena; Gamasa, M. Pilar; Polyhedron; vol. 94; (2015); p. 59 – 66;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

34946-82-2, In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact. Copper(II) trifluoromethanesulfonate, cas is 34946-82-2,the copper-catalyst compound, it is a common compound, a new synthetic route is introduced below.

A solution of imidazo[l,2-b]pyridazine (impy) (758 mg, 6.36 mmol, 10 equiv.) in MeOH (1 mL) was added dropwise at 55C to a solution of Cu(OTf)2 (230 mg, 0.636 mmol, 1.0 equiv.) in MeOH (1 mL). The blue precipitate which formed was washed with Et20 (3 x 2 mL), then recrystallized from hot MeOH to afford [Cu(OTf)2(impy)4] (324 mg, 0.387 mmol. 61%). Anal. Calcd. for C26H2OCUF6NI206S2: C, 37.26; H, 2.41; N, 20.05. Found: C, 37.07; H, 2.33; N, 19.91; IR (ATR, neat): v (cm 1) = 2981, 1620, 1541, 1503, 1374, 1352, 1306, 1281, 1241, 1221, 1149, 1071, 1027, 950, 918, 879, 801, 755, 733, 632.

Chemical properties determine the actual use. Each compound has specific chemical properties and uses. We look forward to more synthetic routes in the future to expand reaction routes of Copper(II) trifluoromethanesulfonate, 34946-82-2

Reference£º
Patent; OXFORD UNIVERSITY INNOVATION LIMITED; GOUVERNEUR, Veronique; CORNELISSEN, Bart; WILSON, Thomas Charles; (152 pag.)WO2019/186135; (2019); A1;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”