copper related catalyst

As a common heterocyclic compound, it belong copper-catalyst compound,[1,3-Bis(2,6-diisopropylphenyl)imidazol-2-ylidene]copper chloride,578743-87-0,Molecular formula: C27H36ClCuN2,mainly used in chemical industry, its synthesis route is as follows.,578743-87-0

General procedure: To an oven-dried screwed 20 mL vial were added (NHC)CuCl (c7 or c8, 0.2 mmol) suspended in dry THF (3 mL); in another vial, [tBu3PN]Li (1b, 42.3 mg, 0.95 eq.) was also dissolved in dry THF (3 mL), then the vial was put into glove-box fridge (-35 C) for one hour. Then the cold mixture was dropped into the (NHC)CuCl/THF suspension slowly under stirring and the suspension was turned into clear solution as the lithium salt added. After addition, the reaction mixture was kept at room temperature in glove box for 13 hours. After the reaction was completed, the volatile was removed under vacuum and dry hexane or pentane (7 mL) was added into the formed oily residue. The suspension obtained was kept stirring for another 15 mins at room temperature, then filtered through a short pad of neutral celite to get rid of precipitate. The filtrate was cooled down in the fridge (-35 C) for 3-4 hours to remove the unreacted lithium salt 1b further. Repeated once again to get the clear hexane or pentane filtrate. The filtrate was evaporated until white crystallized solid was formed, which is the catalytic active species (3 or 4). IPrCuCl (c7, 97 mg, 0.2 mmol); Obtain IPrCuNPtBu3 (3, 99 mg, 78%) as Colorless Solid; 1H NMR (C6D6, 600 MHz) delta 7.26-7.21 (br, m, 4H, m-ArH), 7.17-7.14 (br, m, 2H, p-ArH), 6.40 (s, 2H, NCH=), 2.83 (sep, 4H, J = 6.6 Hz, CH(CH3)2), 1.61 (d, 12H, J = 6.6 Hz, CH(CH3)2), 1.37 (d, 27H, J(PH) = 10.8 Hz, P(C(CH3)3)3), 1.20 (d, 12H, J = 6.6 Hz, CH(CH3)2); 13C NMR (C6D6, 151 MHz) delta 146.18, 136.50, 130.42, 128.68, 124.42, 122.05, 40.78, 40.49, 31.01, 29.33, 25.04, 24.42; 31P NMR (C6D6, 243 MHz) delta 26.35 (s); Elemental analysis calcd for [C39H63CuN3P+0.67 THF]: C, 69.84; H, 9.61; N, 5.86. Found: C, 69.48; H, 9.90; N, 6.19.

With the synthetic route has been constantly updated, we look forward to future research findings about [1,3-Bis(2,6-diisopropylphenyl)imidazol-2-ylidene]copper chloride,belong copper-catalyst compound

Reference£º
Article; Bai, Tao; Yang, Yanhui; Han, Chao; Tetrahedron Letters; vol. 58; 15; (2017); p. 1523 – 1527;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

578743-87-0, [1,3-Bis(2,6-diisopropylphenyl)imidazol-2-ylidene]copper chloride is a copper-catalyst compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

2-(2-Pyridyl)benzimidazole (78.1 mg, 0.4 mmol) was dissolved in 10 mL of dry THF under N2 and this solution was transferred via cannula to suspension of sodium hydride (17.6 mg, 0.44 mmol, 60% in mineral oil) in dry THF. Reaction mixture was stirred at RT for 1 h and then chloro[l,3-bis(2,6-di-i-propylphenyl)imidazol-2- ylidene]copper(I) (195.1 mg, 0.4 mmol) was added. Reaction mixture was stirred at RT for 3 h. The resulting mixture was filtered through Celite and solvent was removed by rotary evaporation. Recrystallization by vapor diffusion of Et20 into a CH2C12 solution of product gave 154 mg (59.5%>) of dark yellow crystals. Anal, calcd. for C39H44CuN5: C, 72.47; H, 6.86; N, 10.48; Found: C, 72.55; H, 6.94; N, 10.84., 578743-87-0

578743-87-0 [1,3-Bis(2,6-diisopropylphenyl)imidazol-2-ylidene]copper chloride 0, acopper-catalyst compound, is more and more widely used in various fields.

Reference£º
Patent; THE UNIVERSITY OF SOUTHERN CALIFORNIA; THOMPSON, Mark; DJUROVICH, Peter; KRYLOVA, Valentina; WO2011/63083; (2011); A1;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

Copper(I) bromide, A common heterocyclic compound, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route. 7787-70-4

7787-70-4, General procedure: To a dry and degassed dichloromethane (10mL) solution of 2,2?-dipyridylamine (1mmol) was added CuX (1mmol). The mixture was kept stirring under nitrogen at ambient temperature. After 1h, a yellow precipitate was formed. To the resulting suspension was added dropwise with stirring a solution of triphenylphosphine (1mmol) in dichloromethane (5mL). The mixture was stirred for another 4h, and then the solvent was evaporated to give a white or yellow residue. The solid residue was extracted with 10mL absolute dichloromethane under the nitrogen atmosphere while the extract was filtered and transferred to a nitrogen-protected flask. 10mL hexane was layered above the resulting solution afforded crystals of the complexes, which were washed with hexane.

7787-70-4 Copper(I) bromide 24593, acopper-catalyst compound, is more and more widely used in various fields.

Reference£º
Article; Wu, Fengshou; Tong, Hongbo; Wang, Kai; Wang, Zheng; Li, Zaoying; Zhu, Xunjin; Wong, Wai-Yeung; Wong, Wai-Kwok; Journal of Photochemistry and Photobiology A: Chemistry; vol. 318; (2016); p. 97 – 103;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

[1,3-Bis(2,6-diisopropylphenyl)imidazol-2-ylidene]copper chloride, cas is 578743-87-0, it is a common heterocyclic compound, the copper-catalyst compound, its synthesis route is as follows.,578743-87-0

Chloro[l ,3-bis(2,6-di-i-propylphenyl)imidazol-2-ylidene]copper(I) (121.9 mg, 0.25 mmol) and silver triflate (64.2 mg, 0.25 mmol) were mixed under nitrogen in 25 mL flask and 10 mL of dry THF were added. Reaction mixture was stirred at RT for 30 minutes. Solution of 1 , 10-phenanthroline (45.05 mg, 0.25 mmol) in dry THF (5 mL) was added. Reaction mixture turned yellow and was stirred at RT overnight. Resulting mixture was filtered through Celite and solvent was evaporated on rotovap. Recrystallization from CH2Ch by vapor diffusion of Et20 gave 120 mg (61.4%) of yellow crystals. Anal, calcd. for C40H44CUF3N4O3S: C, 61.48; H, 5.68; N, 7.17; Found: C, 61.06; H, 5.61; N, 7.14. Structure was confirmed by IH-NMR spectrum of [(IPR)Cu(phen)]OTf (CDCb, 400MHz).

578743-87-0 is used more and more widely, we look forward to future research findings about [1,3-Bis(2,6-diisopropylphenyl)imidazol-2-ylidene]copper chloride

Reference£º
Patent; THE UNIVERSITY OF SOUTHERN CALIFORNIA; THOMPSON, Mark; DJUROVICH, Peter; KRYLOVA, Valentina; WO2011/63083; (2011); A1;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact.6046-93-1, Copper(II) acetate hydrate it is a common compound, a new synthetic route is introduced below., 6046-93-1

Bis(8-quinolinolato)copper(II) was synthesized as follows. In a typical synthesis, 1.45 g (10 mmol) of 8-quinolinol ligand was dissolved in 20 ml THF, followed by the dropwise addition of a solution of 1.0 g (5 mmol) Cu(CH3COO)2*H2O in 10ml THF at reflux temperature. The resultant solution was stirred and refluxed for 2 h. After cooling, the solid product was separated by filtration and denoted as CuQ2.

As the rapid development of chemical substances, we look forward to future research findings about 6046-93-1

Reference£º
Article; Hu, Jing; Zou, Yongcun; Liu, Jing; Sun, Jian; Yang, Xiaoyuan; Kan, Qiubin; Guan, Jingqi; Research on Chemical Intermediates; vol. 41; 8; (2015); p. 5703 – 5712;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

7787-70-4, A common heterocyclic compound, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route., 7787-70-4

To a solution of CuBr (0.0135 g, 0.094 mmol) in 10 mL of acetonitrile was added dropwise 1 (0.03 g, 0.094 mmol) in dichloromethane (5 mL) at room temperature. The reaction mixture was stirred for 4 h. The solvent was removed under reduced pressure to get 6 as a pale yellow solid. Analtyically pure product of 6 was obtained by recrystallizing the crude product in a 1:2 mixture of dichloromethane and petroleum ether. Yield: 81% (0.035 g). Mp: 158-160 C. Anal. Calc. for C42H44Cu2Br2N2P2: C, 54.66; H, 4.80; N, 3.03. Found: C, 54.95; H, 4.85; N, 2.88%. 1H NMR (400 MHz, CDCl3): delta 7.52-6.83 (m, Ar, 28H), 3.50 (s, CH2, 4H), 2.42 (s, NMe2, 12H). 31P{1H} NMR (162 MHz, CDCl3): delta -16.2 (br s). MS (EI): m/z 845.22 [M-Br]+.

With the synthetic route has been constantly updated, we look forward to future research findings about Copper(I) bromide,belong copper-catalyst compound

Reference£º
Article; Ananthnag, Guddekoppa S.; Edukondalu, Namepalli; Mague, Joel T.; Balakrishna, Maravanji S.; Polyhedron; vol. 62; (2013); p. 203 – 207;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

13395-16-9, Bis(acetylacetone)copper is a copper-catalyst compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

General procedure: In a typical synthesis of Cu40Ag60, 0.45mmol Cu(acac)2 and 0.35 Ag (ac) was mixed with 3mL of OAm, 1 mL of OAc and 11mL of ODE. All synthesis was conducted in a four-necked glass reactor allowing the precise temperature control and inert gas atmosphere under dark conditions. Firstly, the mixture was heated to 60C and kept at this temperature for 10min. Then, the mixture was heated to 180C and kept at this temperature for 30min before it was cooled down to room temperature. After cooling, the resultant reaction mixture was collected with hexane (2mL) and the NPs were separated by centrifugation (8500rpm, 12min) after adding isopropanol (40mL). To further purify the yielded CuAg NPs, the product was centrifuged (8500rpm, 12min) one more time with ethanol (40mL). Finally, the remaining product was dispersed in hexane (10mL) for further use. By using the same recipe and varying metal precursor amounts, two different compositions of CuAg NPs were synthesized. Reductive mixing of 0.3mmol Cu(acac)2 and 0.5 Ag(ac) resulted in Cu30Ag70 NPs and mixing 0.6mmol Cu(acac)2 with 0.4 Ag (ac) led to Cu60Ag40. Synthesis of Ag NPs was conducted with the same recipe without using Cu precursor.

13395-16-9, As the paragraph descriping shows that 13395-16-9 is playing an increasingly important role.

Reference£º
Article; Balkan, Timucin; Kuecuekkececi, Hueseyin; Kaya, Sarp; Metin, Oender; Zarenezhad, Hamaneh; Journal of Alloys and Compounds; vol. 831; (2020);,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.34946-82-2,Copper(II) trifluoromethanesulfonate,as a common compound, the synthetic route is as follows.

To a solution of ligand L1 (50 mg, 0.2 mmol) in ethyl acetate(3 mL) was added a saturated solution of copper(II) trifluoromethanesulfonate(Cu(OTf)2) in ethyl acetate (2 mL).A blue-green precipitate appeared within 10 min, whichwas transformed into green-brown hexagonal crystalsduring slow evaporation of the solvent on standing withair contact. The crystals were collected by filtration withsuction, washed with a small volume of ethyl acetate toremove co-precipitated Cu(OTf)2. Yield: 85 mg (95%); M.p.272-274C. – IR (KBr): = 3262 m br (NH), 3147 w, 3103w, 1645 m, 1597 s, 1296 vs, 1253 vs, 1228 s, 1148 s, 1076 m,1059 m, 1029 vs, 757 w, 729 s, 629 s, 575 m, 520 m cm-1. -MS ((+)-MALDI-TOF): m/z (%) = 666.24 (100) [M-CF3SO3]+,516.26 (15) [M-2CF3SO3-H]+, 228.16 (74) [L1+H]+. – Anal. forC26H26CuF6N10O6S2 (816.21): calcd. C 38.26, H 3.21, N 17.16;found C 38.25, H 3.49, N 16.92.

34946-82-2, As the paragraph descriping shows that 34946-82-2 is playing an increasingly important role.

Reference£º
Article; Schroeder, Sven; Frey, Wolfgang; Maas, Gerhard; Zeitschrift fur Naturforschung, B: Chemical Sciences; vol. 71; 6; (2016); p. 683 – 696;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

34946-82-2, Copper(II) trifluoromethanesulfonate is a copper-catalyst compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

Was added to the Schlenk tube Cu(OTf)2 (0.01mmol), ligand (Ra,S,S)-I-Ph (0.01mmol) N2 protection, the solvent was added CHCl3(2 mL), stirred at room temperature for 4 hours ligand, and concentrated under reduced pressure, vacuum drained, i.e., quantitative complex to give [(Ra,S,S)-I-Ph]Cu(OTf)2.

34946-82-2, As the paragraph descriping shows that 34946-82-2 is playing an increasingly important role.

Reference£º
Patent; Zhejiang University; Lin Xufeng; Gu Haorui; Sun Weiye; (21 pag.)CN108794420; (2018); A;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

The copper-catalyst compound, cas is 34946-82-2 name is Copper(II) trifluoromethanesulfonate, mainly used in chemical industry, its synthesis route is as follows.,34946-82-2

A saturated solution of Cu(OTf)2 in n-butanol was addeddrop by drop to a solution of ligand L5 (40 mg, 0.16 mmol) in n-butanol (3 mL). Diethyl ether was placed on top of theblue butanol layer. After several weeks, deep blue crystalplatelets separated which were isolated by filtration withsuction, washed with a small volume of diethyl ether anddried at air. Yield: 64 mg (91); M.p. 271-275C. – IR (KBr): = 3322 br, 3154 w br, 3063 w, 1641 m, 1613 s, 1453 m, 1284vs, 1256 vs, 1225 vs, 1167 s, 1032 vs, 759 m, 700 s, 639 vs,576 m, 518 m cm-1. – Anal. for C28H30CuF6N10O6S2 (844.27):calcd. C 39.83, H 3.58, N 16.59; found C 40.07, H 3.74, N 16.16.

As the rapid development of chemical substances, we look forward to future research findings about 34946-82-2

Reference£º
Article; Schroeder, Sven; Frey, Wolfgang; Maas, Gerhard; Zeitschrift fur Naturforschung, B: Chemical Sciences; vol. 71; 6; (2016); p. 683 – 696;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”