Some scientific research about Copper(II) trifluoromethanesulfonate

With the complex challenges of chemical substances, we look forward to future research findings about 34946-82-2,belong copper-catalyst compound

As a common heterocyclic compound, it belongs to copper-catalyst compound, name is Copper(II) trifluoromethanesulfonate, and cas is 34946-82-2, its synthesis route is as follows.,34946-82-2

The complex was prepared according a known procedure [11] , starting from LHMe2 (0.157?g, 1?eq) dissolved in acetone (10?ml) and Et3N (150?mul). A solution of Cu(OTf)2 (0.272?g, 2.1?eq) in acetonitrile (10?ml) was added, and the mixture was stirred for 1?h. The mixture was then concentrated, di-isopropylether (10?ml) was added and the solution was placed at -20?C for 1?week to give the pure complex [Cu2(LMe2)(mu-OH)][OTf] (73?mg, 28%) as a dark solid. ESI-MS (CH3CN), m/z: z?=?1, 589 (M-OTf)+, UV-Vis (CH3CN) (epsilon, M-1?cm-1): 242 (23000), 281 (14000), 326 (16000) 338 (16000), 390 (18000), 760 (185) Anal. Calcd. for C25H27Cu2N6O5S2F3: C, 40.59; H, 3.68; N, 11.36. Found C, 40.62; H, 3.85; N, 11.13.

With the complex challenges of chemical substances, we look forward to future research findings about 34946-82-2,belong copper-catalyst compound

Reference£º
Article; Gennarini, Federica; Kochem, Amelie; Isaac, James; Mansour, Ali-Taher; Lopez, Isidoro; Le Mest, Yves; Thibon-Pourret, Aurore; Faure, Bruno; Jamet, Helene; Le Poul, Nicolas; Belle, Catherine; Simaan, A. Jalila; Reglier, Marius; Inorganica Chimica Acta; vol. 481; (2018); p. 113 – 119;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

 

Application of 5,10,15,20-Tetraphenyl-21H,23H-porphine copper(II)

With the complex challenges of chemical substances, we look forward to future research findings about 5,10,15,20-Tetraphenyl-21H,23H-porphine copper(II)

Name is 5,10,15,20-Tetraphenyl-21H,23H-porphine copper(II), as a common heterocyclic compound, it belongs to copper-catalyst compound, and cas is 14172-91-9, its synthesis route is as follows.,14172-91-9

To 0.025 g (0.0296 mmol) of copper tetraphenylporphyrin in a mixture of 10 mL ofCHCl3 and 1mL of DMF was added 0.105 g (0.592 mmol) of NBS and stirred at roomtemperature for 10 h. The reaction mixture was evaporated to a minimum 10 mL ofDMF, H2O and NaClsolid was added. Dark brown precipitate was filtered off, washedwith water and dried, then chromatographed on Al2O3 with CHCl3, and precipitatedfrom C25OH. Yield: 68% (0.026 g, 0.0199 mmol). Mass spectrum, m/z (Irel, %) 1306.6(98) [M]+ was calculated for C44H20N4Br8Cu – 1307.5. UV-vis spectrum in CHCl3, lambda, nm(log epsilon)626 sh., 581 (4.33), 467 (5.21), 447 sh

With the complex challenges of chemical substances, we look forward to future research findings about 5,10,15,20-Tetraphenyl-21H,23H-porphine copper(II)

Reference£º
Article; Chizhova, Natalya Vasil?evna; Maltceva, Olga Valentinovna; Zvezdina, Svetlana Veniaminovna; Mamardashvili, Nugzar Zhoraevich; Koifman, Oscar Iosifovich; Journal of Coordination Chemistry; vol. 71; 19; (2018); p. 3222 – 3232;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

 

Extracurricular laboratory: Synthetic route of Bis(acetylacetone)copper

As the rapid development of chemical substances, we look forward to future research findings about 13395-16-9

A common heterocyclic compound, the copper-catalyst compound, name is Bis(acetylacetone)copper,cas is 13395-16-9, mainly used in chemical industry, its synthesis route is as follows.

13395-16-9, General procedure: CZTS nanoparticles were synthesized at different temperatures(220-320 C) for 3 hours and for variousreaction times (2-5 hours) at 240 C, usinghigh-temperature arrested precipitation in the coordinatingsolvent, oleylamine (OLA).15 Under the reactiontime of 3 hours, the reactants for synthesis ofCZTS nanoparticles didn?t dissolve enough in OLA.

As the rapid development of chemical substances, we look forward to future research findings about 13395-16-9

Reference£º
Article; Kim, Donguk; Kim, Minha; Shim, Joongpyo; Kim, Doyoung; Choi, Wonseok; Park, Yong Seob; Choi, Youngkwan; Lee, Jaehyeong; Journal of Nanoscience and Nanotechnology; vol. 16; 5; (2016); p. 5082 – 5086;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

 

A new synthetic route of Copper(II) trifluoromethanesulfonate

As the rapid development of chemical substances, we look forward to future research findings about 34946-82-2

Copper(II) trifluoromethanesulfonate, cas is 34946-82-2, it is a common heterocyclic compound, the copper-catalyst compound, its synthesis route is as follows.,34946-82-2

A solution of Cu(OTf)2 (90.0 mg, 0.249 mM, OTf = trifluormethansulfonate) in methanol was added to a solution of HLpz (53.5 mg,0.250 mM) and triethylamine (25.0 mg, 0.250 mM) in methanol, affording a dark green solution. A solution of excess 4,4-bipyridine (4,4-bipy) was layered on the above solution, from which purple crystals of 1 suitable for X-ray analysis were obtained. Yield: 86 mg, 68%. Anal. Calcd for C34H26Cu2F6N10O8S2: C, 40.52; H, 2.60; N, 13.90. Found: C, 40.27;H, 2.53; N, 13.63. FTIR (KBr): 3447, 1647, 1416, 1380, 1291, 1245, 1224, 1158, 1033,816, 772, 638, 518 cm-1. ESI-MS (MeOH): m/z = 276 [Cu(Lpz)]+, 432 [Cu(Lpz)(4,4-bipy)]+, 490 [Cu(Lpz)2 + H]+.

As the rapid development of chemical substances, we look forward to future research findings about 34946-82-2

Reference£º
Article; Houser, Robert P.; Wang, Zhaodong; Powell, Douglas R.; Hubin, Timothy J.; Journal of Coordination Chemistry; vol. 66; 23; (2013); p. 4080 – 4092;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

 

Share a compound : Copper(II) trifluoromethanesulfonate

34946-82-2 is used more and more widely, we look forward to future research findings about Copper(II) trifluoromethanesulfonate

Copper(II) trifluoromethanesulfonate, cas is 34946-82-2, it is a common heterocyclic compound, the copper-catalyst compound, its synthesis route is as follows.,34946-82-2

Cu (CF3 SO3 )2 And 4 – (3 – (4H – 1,2, 4 – triazole -4 – yl) phenyl) – 4H – 1,2, 4 – triazole) (L) in a molar ratio of 1:1; L (0.0424 g, 0.2 mmol), Cu (CF3 SO3 )2 (0.0691 g, 0.2 mmol), H2 O (6 ml), CH3 CN (4 ml), water heat 160 o C three days after cooling to room temperature. After operates the cauldron X – ray single crystal diffraction analysis is yellow rod-like crystal. Yield: 35% (calculated on the basis of L). Elemental analysis (C33 H26 Cu3 F9 N18 O10 S3 ) Theoretical value (%): C, 30.67; H, 2.03; N, 19.51. The measured value: C, 30.69; H, 2.06; N, 19.59. We also tried other proportions, for example Cu (CF3 SO3 )2 And L in a molar ratio of 2:1, irrespective of the length of the water heat reaction time, are not crystalline compound. Therefore Cu (CF3 SO3 )2 And L in a molar ratio of 1:1 is the best reaction mixture ratio.

34946-82-2 is used more and more widely, we look forward to future research findings about Copper(II) trifluoromethanesulfonate

Reference£º
Patent; Tianjin Normal University; Wang, Ying; (12 pag.)CN104557982; (2017); B;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

 

Some tips on Copper(I) bromide

The synthetic route of 7787-70-4 has been constantly updated, and we look forward to future research findings.

As we all know, there are many different methods for the synthesis of a compound, and people can choose the synthesis method that suits their own laboratory according to the actual situation. 7787-70-4, Copper(I) bromide. This compound is widely used in many fields, so it is necessary to find a new synthetic route. The downstream synthesis method of this compound is introduced below.7787-70-4

7787-70-4, General procedure: The complexes were prepared according to the following method [14]: 1mmol of copper(I) bromide or copper(I) chloride is stirred in methanol until complete dissolution. Then, 2.1mmol of the corresponding phosphine ligand was added. The mixture was stirred at 60C for 30min. under nitrogen atmosphere. A microcrystalline precipitate was obtained by concentration of the solution at reduced pressure. The solid product was dissolved in a dichloromethane/methanol mixture and the solution was gradually cooled to 4C to give an air stable and colorless crystalline solid suitable for X-ray single-crystal diffraction studies.

The synthetic route of 7787-70-4 has been constantly updated, and we look forward to future research findings.

Reference£º
Article; Espinoza, Sully; Arce, Pablo; San-Martin, Enrique; Lemus, Luis; Costamagna, Juan; Farias, Liliana; Rossi, Miriam; Caruso, Francesco; Guerrero, Juan; Polyhedron; vol. 85; (2014); p. 405 – 411;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

 

A new synthetic route of Copper(II) trifluoromethanesulfonate

As the rapid development of chemical substances, we look forward to future research findings about 34946-82-2

The copper-catalyst compound, cas is 34946-82-2 name is Copper(II) trifluoromethanesulfonate, mainly used in chemical industry, its synthesis route is as follows.,34946-82-2

To a solution of 2.00 g (4.82 mmol) of the above ieri-butyl ester in dimethylsulfoxide (15 mL) is added 1.10 mL (10.1 mmol) of dimethylethylenediamine followed by 0.983 g (9.64 mmol) of sodium methanesulfinate, and 1.74 g (4.82 mmol) of copper (II) triflate. The mixture is heated at 130 C under argon for 2 hours. The mixture is cooled to room temperature and diluted with water causing a solid to precipitate from solution. The formed solid is collected by filtration, washed with water, and dried on the filter pad. The residue is purified by flash silica gel chromatography to give 1.03 g (52.0%) of (5′- methanesulfonyl-3′-nitro-3,4,5,6-tetrahydro-2H-[l,2′]bipyridinyl-4-ylmethyl)-carbamic acid ie/ -butyl ester as a brown resin.

As the rapid development of chemical substances, we look forward to future research findings about 34946-82-2

Reference£º
Patent; BOEHRINGER INGELHEIM INTERNATIONAL GMBH; GINN, John David; SORCEK, Ronald John; TURNER, Michael Robert; WU, Di; WU, Frank; WO2011/84985; (2011); A1;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

 

Analyzing the synthesis route of Copper(I) bromide

As the paragraph descriping shows that 7787-70-4 is playing an increasingly important role.

Each compound has different characteristics, and only by selecting the characteristics of the compound suitable for a specific situation can the compound be applied on a large scale. 7787-70-4, name is Copper(I) bromide. This compound has unique chemical properties. The synthetic route is as follows. 7787-70-4

General procedure: HLBAP (0.525 g, 1 mmol) and triethylamine (0.28 mL, 2 mmol) were dissolved in a 2:1 acetonitrile/dichloromethane mixture (45 ml), and then copper salt with the corresponding anion (1 mmol) was added. The reaction mixture was stirred for 4 h at room temperature in the presence of air. X-ray quality red brown crystals were grown from a 1:1 solvent mixtureof dichloromethane/methanol., 7787-70-4

As the paragraph descriping shows that 7787-70-4 is playing an increasingly important role.

Reference£º
Article; Safaei, Elham; Bahrami, Hadiseh; Wojtczak, Andrzej; Alavi, Saman; Jagli?i?, Zvonko; Polyhedron; vol. 122; (2017); p. 219 – 227;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

 

Brief introduction of [1,3-Bis(2,6-diisopropylphenyl)imidazol-2-ylidene]copper chloride

578743-87-0 is used more and more widely, we look forward to future research findings about [1,3-Bis(2,6-diisopropylphenyl)imidazol-2-ylidene]copper chloride

[1,3-Bis(2,6-diisopropylphenyl)imidazol-2-ylidene]copper chloride, cas is 578743-87-0, it is a common heterocyclic compound, the copper-catalyst compound, its synthesis route is as follows.,578743-87-0

2-(2-Pyridyl)benzimidazole (78.1 mg, 0.4 mmol) was dissolved in 10 mL of dry THF under N2 and this solution was transferred via cannula to suspension of sodium hydride (17.6 mg, 0.44 mmol, 60% in mineral oil) in dry THF. Reaction mixture was stirred at RT for 1 h and then chloro[l,3-bis(2,6-di-i-propylphenyl)imidazol-2- ylidene]copper(I) (195.1 mg, 0.4 mmol) was added. Reaction mixture was stirred at RT for 3 h. The resulting mixture was filtered through Celite and solvent was removed by rotary evaporation. Recrystallization by vapor diffusion of Et20 into a CH2C12 solution of product gave 154 mg (59.5%>) of dark yellow crystals. Anal, calcd. for C39H44CuN5: C, 72.47; H, 6.86; N, 10.48; Found: C, 72.55; H, 6.94; N, 10.84.

578743-87-0 is used more and more widely, we look forward to future research findings about [1,3-Bis(2,6-diisopropylphenyl)imidazol-2-ylidene]copper chloride

Reference£º
Patent; THE UNIVERSITY OF SOUTHERN CALIFORNIA; THOMPSON, Mark; DJUROVICH, Peter; KRYLOVA, Valentina; WO2011/63083; (2011); A1;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

 

Share a compound : Bis(acetylacetone)copper

The chemical industry reduces the impact on the environment during synthesis,13395-16-9,Bis(acetylacetone)copper,I believe this compound will play a more active role in future production and life.

13395-16-9, In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact. Bis(acetylacetone)copper, cas is 13395-16-9,the copper-catalyst compound, it is a common compound, a new synthetic route is introduced below.

General procedure: In a typical synthesis of Cu40Ag60, 0.45mmol Cu(acac)2 and 0.35 Ag (ac) was mixed with 3mL of OAm, 1 mL of OAc and 11mL of ODE. All synthesis was conducted in a four-necked glass reactor allowing the precise temperature control and inert gas atmosphere under dark conditions. Firstly, the mixture was heated to 60C and kept at this temperature for 10min. Then, the mixture was heated to 180C and kept at this temperature for 30min before it was cooled down to room temperature. After cooling, the resultant reaction mixture was collected with hexane (2mL) and the NPs were separated by centrifugation (8500rpm, 12min) after adding isopropanol (40mL). To further purify the yielded CuAg NPs, the product was centrifuged (8500rpm, 12min) one more time with ethanol (40mL). Finally, the remaining product was dispersed in hexane (10mL) for further use. By using the same recipe and varying metal precursor amounts, two different compositions of CuAg NPs were synthesized. Reductive mixing of 0.3mmol Cu(acac)2 and 0.5 Ag(ac) resulted in Cu30Ag70 NPs and mixing 0.6mmol Cu(acac)2 with 0.4 Ag (ac) led to Cu60Ag40. Synthesis of Ag NPs was conducted with the same recipe without using Cu precursor.

The chemical industry reduces the impact on the environment during synthesis,13395-16-9,Bis(acetylacetone)copper,I believe this compound will play a more active role in future production and life.

Reference£º
Article; Balkan, Timucin; Kuecuekkececi, Hueseyin; Kaya, Sarp; Metin, Oender; Zarenezhad, Hamaneh; Journal of Alloys and Compounds; vol. 831; (2020);,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”